|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M General Description Combining low-power CMOS logic with high-current, high-voltage power FET outputs, the Series SLA705xM translator/driver provides complete control and drive for a two-phase unipolar stepper motor with internal fixed off time, pulse-width modulation (PWM) control of the output current in a power multi-chip module (PMCMTM). The CMOS logic section provides the sequencing logic, direction, full/half-step control, synchronous/asynchronous PWM operation, and a "sleep" function. The minimum CLOCK input is an ideal fit for applications where a complex P is unavailable or overburdened. TTL or LSTTL may require the use of appropriate pull-up resistors to ensure a proper input-logic high. For PWM current control, the maximum output current is determined by the user's selection of a reference voltage and sensing resistor. The NMOS outputs are capable of sinking up to 1,2 or 3 A and withstanding 46 V in the off state. Ground-clamp and flyback diodes provide protection against inductive transients. Special power-up sequencing is not required. Full-step (2 phase) and half-step operation are externally selectable. Two-phase drive energizes two adjacent phases in each detent position (AB-BC-CD-DA). This sequence mode offers an improved torquespeed product, greater detent torque, and is less susceptable to motor resonance. Half-step excitation alternates between the one-phase and two-phase modes (A-AB-B-BC-C-CD D-DA), providing an eight-step sequence. October 2005 Package----SLA18Pin Applications PPC Printer OA Equipment Key Specifications Motor Supply Voltage (VM)44V max Load Supply Voltage (Vs)10V44V Logic Supply Voltage (Vcc)3V5.5V Output Current (Io)1A(SLA7050M) 2A(SLA7051M) 3A(SLA7052M) Output Maximum Voltage (VDSS)100V min Features To 3A Output Rating Internal Sequencer for Full or Half-Step Operation PWM Constant-Current Motor Drive Cost-Effective, Multi-Chip Solution 100 V, Avalanche-Rated NMOS Low rDS(on) NMOS Outputs (300 milli-ohms typical) Advanced, Improved Body Diodes Half-Step and Full-Step Unipolar Drive Inputs Compatible with 3.3 V or 5 V Control Signals Sleep Mode Internal Clamp Diodes Typical Connection Vs=10V 44V 1 3 14 16 18 Vcc=3.0V5.5V Disable CA 5 Q1 r1 7 8 11 12 9 OutA OutA/ Vcc Vs OutB/ OutB NC GA GB NC SenseB 13 2 4 15 17 CB Clock SLA M Sync SLA M CW/CCW Full/Half Ref SenseA Gnd 6 10 SLA M r2 RsA RsB S-Gnd Gnd P-Gnd Sanken Electric Co.,Ltd. http://www.sanken-ele.co.jp/en/ I03-002EA-051006 1/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Scope October 2005 The present specifications shall apply to Sanken 2 Phase Stepper Motor Driver IC,SLA705xM Series. The present specifications shall apply to SLA 705xM Series which is performed RoHS instructions. Lead part solderPb free Inner solderLead content 85% Outline Type Structure Applications Hybrid integrated circuit Plastic molded (transfer mold) To drive a 2 phase stepper motor. (Full or Half Step. PWM Current Control.) Absolute maximum ratings Characteristic Motor Supply Voltage Load Supply Voltage Logic Supply Voltage Symbol VM VS Vcc Ratings 46 46 7 1.0 Output Current Io 2.0 3.0 Logic Input Voltage REF Input Voltage Sense Voltage Total Device Dissipation Junction Temperature Operating Temperature Range Storage Temperature Range VIN VREF VRs PD Tj Ta Tstg 0.3Vcc0.3 0.3Vcc0.3 22 4 20 150 2085 30150 V V V W W Tw<1S doesn't contain it. at Ta=25 at Tc=25 A Unit V V V SLA7050M SLA7051M SLA7052M Remarks Sanken Electric Co.,Ltd. I03-002EA-051006 2/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Electrical characteristics Recommendable Operating Range Characteristic Motor Supply Voltage Load Supply Voltage Logic Supply Voltage REF Input Voltage Package Temperature Symbol VM VS Vcc VREF Tc 10 3.0 0.1 Ratings MIN MAX 44 44 5.5 1.0 100 Unit V V V V October 2005 Remarks Please adjust the Vcc surge voltage to 0.5V or less. The control current accuracy decreases in 0.1V or less. 10Pin temperature at No Fin Electrical Characteristic (Ta=25,Vs=24V,Vcc=5V Unless Otherwise Noted) Characteristic Load Supply Current Logic Supply Current Output Maximum Voltage FET On-State Resistance FET Diode Forward Voltage Maximum Clock Frequency Logic Input Voltage Logic Input Current REF Input Voltage REF Input Current Sense Voltage Symbol IS ISS Icc VDSS RDS(on) VSD Fclock VIL VIH IIL IIH VREF VREFS IREF VRs Vccx0.75 1 1 0 2.0 10 VREF 1.5 Vcc 100 0.3 0.8 0.5 1.1 100 Vccx0.25 MIN Limits TYP MAX 15 100 3 Unit mA A mA V V kHz V V A A V V A V Stationary current control Output OFF(Sleep) Test Condition Regularity atSLEEPoperates VS=44V IDSS=1mA ID=1A ISD=1A Sanken Electric Co.,Ltd. I03-002EA-051006 3/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Electrical Characteristic (Ta=25,Vs=24V,Vcc=5V Unless Otherwise Noted) Characteristic PWM OFF Time PWM Minimum ON Time Sleep-Enable return time Switching Time Symbol TOFF TON(min) TSE TONC TOFFC 100 2.5 2.0 MIN Limits TYP 12 5 MAX Unit S S S S S October 2005 Test Condition 2.0 V 1.5 VREF Io A 1.5 ClockOut ClockOut Truth table Pin Function CWCCW FullHalf REF Sync Clock Low level Forward(CW) Full Step Enable Non synchronous PWM Positive Edge High level Reverse(CCW) Half Step Output disable(Sleep) Synchronous PWM Input Logic Timing 10S(min) Clock 5S(min) 5S(min) CWCCW & FullHalf 2S(min) 2S(min) 2S(min) 2S(min) Sanken Electric Co.,Ltd. I03-002EA-051006 4/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Timing chart October 2005 Step Vcc Clock CW/CCW F/H OUT_ A OUT_ /A OUT_ B OUT_ /B 0 2 4 6 0 2 4 2 0 6 5 4 3 2 1 0 7 6 5 6 7 0 1 2 4 6 0 This timing chart is a voltage mark. PWM signal for current control is not superimposed on this timing chart. Sanken Electric Co.,Ltd. I03-002EA-051006 5/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Heat design data Total PowerT indegc October 2005 150 125 100 T () j-a=31.25(/W) Ta=25 Air cooling without blower (No Fin) 75 50 25 0 0 1 2 3 Total Power P (W) c-a=27.5(/W) Tj-a Tc-a 4 5 The temperature of the case is 10pin. TaP 4.5 4 Allowable Package Power Dissipation in Watts (W) 3.5 3 2.5 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 Ambient Temperature () 80 90 100 j-a=31.25(/W) Sanken Electric Co.,Ltd. I03-002EA-051006 6/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Block diagram (Connection diagram) Full/Half CW/CCW OutA 1 6 SenseA OutA/ 3 Clock OutB/ N.C. 2 N.C. Vcc GA 4 Vs 14 GB October 2005 OutB 11 12 7 5 15 17 16 18 MIC GA OSC GA/ Reg GB Sequencer GB/ OSC PWM Control Synchro Control Sleep Control PWM Control 9 Ref 8 Sync 10 Gnd 13 SenseB Pin arrangement ,Functional table Symbol Function 1 OutA Phase A Output 2 N.C. No Contact 3 OutA/ Phase A/ Output GA 4 Phase A Gate 5 Vcc Logic supply 6 SenseA Phase A current sense 7 Clock Step clock 8 Sync Synchronous PWM control 9 Ref Current reference & Output disable 10 GND GND 11 CW/CCW Forward reverse control 12 Full/Half Full step half step control 13 SenseB Phase B current sense 14 Vs Load supply GB 15 Phase B Gate 16 OutB/ Phase B/ Output 17 N.C. No Contact 18 OutB Phase B Output The gating signal of MOS FET outputs, and use 4pin and 15pin by the unwiring, please. Pin Number Sanken Electric Co.,Ltd. I03-002EA-051006 7/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Example application circuit Vs=10V 44V October 2005 1 3 14 16 18 Vcc=3.0V 5.5V Disable 5 Q1 r1 7 8 11 12 9 Out Vcc A OutA/ Vs OutB/ Out B NC GA GB NC 2 4 15 17 CA CB Clock Sync CW/ CCW Full/Half Ref SenseA 6 SLA7050M SLA7051M SLA7052M Gnd 10 SenseB 13 r2 RsA RsB S-Gnd Gnd P-Gnd Reference constant Rs=0.12(Loss attention PIo2xRs) R1=10k R2=5.1k(VR) CA=100F50V CB=10F10V Q1 Be careful of especially the noise on Vcc line. If the noise on Vcc line exceeds 0.5V, a product may incorrect-operate. When you do not use Logic inputs (CW/CCW and F/H, Sync), please be sure to connect with Vcc or GND. To minimize the effect of system ground IR drops on the logic and reference input signals, Ground pin should have a low-impedance return to system groud. 2pin,4pin,15pin and 17pin are No Contact. Sanken Electric Co.,Ltd. I03-002EA-051006 8/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Package information Package type and physical dimensions October 2005 a b a. Type Number SLA705xM Dimensions in mm b. Lot Number 1st letter The last digit of year 2nd letter Month 19 Arabic Numerals 10 O 11 N 12 D (1 to 9 for Jan. to Sept. O for Oct. N for Nov. D for Dec.) 3rd &4th letter day 0131 Arabic Numerals Appearance The body shall be clean and shall not bear any stain, rust or flaw. Marking The type number and lot number shall be clearly marked in white. Sanken Electric Co.,Ltd. I03-002EA-051006 9/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Packing specifications October 2005 31 580 A rubber stopper is provided on both ends of the stick. 18 pieces in X direction (Maximum 18 pieces in one stick) 8 X 130 610 20 sticks in Y direction 3 sticks in Y direction 185 Z Y 18piecesx20x3=1080pieces(Max.) Dimensions in mm Sanken Electric Co.,Ltd. I03-002EA-051006 10/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Cautions and warnings The calculation of control current SLA705xM Series control current Io is calculated as follow. IoVREFRs REF Voltage range is 0.1V1.0V When the REF<0.1V, the accuracy of control current is reduce. October 2005 Moreover, if REF voltage is set up more than 2.0V, all outputs will be in OFF state. Installation to a heat sink 1)Recommended Clamping Torque (to External Heat sink) 0.4900.822Nm 2)Recommended Silicone SHIN-ETSU CHEMICAL G746 YG6260 GE TOSHIBA SILICONES SC102 DOW CORNING TORAY SILICONE Notice This driver has C-MOS inputs. Please notice as following contents. When static electricity is a problem, care should be taken to properly control the room humidity. This is particularly true in the winter when static electricity is most troublesome. Care should be taken with device leads and with assembly sequencing to avoid applying static charges to IC leads. PC board pins should be shorted together to keep them at the same potential to avoid this kind of trouble. Sanken Electric Co.,Ltd. I03-002EA-051006 11/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M October 2005 Asia Pacific China Sanken Electric Hong Kong Co., Ltd. Suite 1026 Ocean Centre, Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 852-2735-5262 Fax: 852-2735-5494 Sanken Electric (Shanghai) Co., Ltd. Room3202, Maxdo Centre, Xingyi Road 8, Changning district, Shanghai, China Tel: 86-21-5208-1177 Fax: 86-21-5208-1757 Taiwan Sanken Electric Co., Ltd. Room 1801, 18th Floor, 88 Jung Shiau East Road, Sec. 2, Taipei 100, Taiwan R.O.C. Tel: 886-2-2356-8161 Fax: 886-2-2356-8261 India Saket Devices Pvt. Ltd. Office No.13, First Floor, Bandal - Dhankude Plaza, Near PMT Depot, Paud Road, Kothrud, Pune - 411 038, India Tel: 91-20-5621-2340 91-20-2528-5449 Fax: 91-20-2528-5459 Japan Sanken Electric Co., Ltd. Overseas Sales Headquaters Metropolitan Plaza Bldg. 1-11-1 Nishi-Ikebukuro, Toshima-ku, Tokyo 171-0021, Japan Tel: 81-3-3986-6164 Fax: 81-3-3986-8637 Korea Sanken Electric Korea Co., Ltd. Mirae Asset Life Bldg. 6F, 168 Kongduk-dong, Mapo-ku, Seoul, 121-705, Korea Tel: 82-2-714-3700 Fax: 82-2-3272-2145 Singapore Sanken Electric Singapore Pte. Ltd. 150 Beach Road, #14-03 The Gateway West, Singapore 189720 Tel: 65-6291-4755 Fax: 65-6297-1744 Sanken Electric Co.,Ltd. I03-002EA-051006 12/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M Europe United Kingdom Sanken Power Systems (UK) Limited Pencoed Technology Park, Pencoed, Bridgend CF35 5HY. UK Tel: 44-1656-869-100 Fax: 44-1656-869-162 October 2005 North America United States Allegro MicroSystems, Inc. 115 Northeast Cutoff, Worcester, Massachusetts 01606, U.S.A. Tel: 1-508-853-5000 Fax: 1-508-853-3353 Allegro MicroSystems, Inc. (Southern California) 14 Hughes Street, Suite B105, Irvine, CA 92618 Tel: 1-949-460-2003 Fax: 1-949-460-7837 Sanken Electric Co.,Ltd. I03-002EA-051006 13/14 2-Phase Unipolar Stepper Motor Driver SLA7050M/7051M/7052M CAUTION / WARNING October 2005 The information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Sanken reserves the right to make changes without further notice to any products herein in the interest of improvements in the performance, reliability, or manufacturability of its products. Before placing an order, Sanken advises its customers to obtain the latest version of the relevant information to verify that the information being relied upon is current. Application and operation examples described in this catalog are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. When using the products herein, the applicability and suitability of such products for the intended purpose or object shall be reviewed at the users' responsibility. Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure nd defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. Sanken products listed in this catalog are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). Before placing an order, the user's written consent to the specifications is requested. When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), please contact your nearest Sanken sales representative to discuss and obtain written confirmation of your specifications. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. Anti radioactive ray design is not considered for the products listed herein. This publication shall not be reproduced in whole or in part without prior written approval from Sanken. This is notification that you, as purchaser of the products/technology, are not allowed to perform any of the following: 1. Resell or retransfer these products/technology to any party intending to disturb international peace and security. 2. Use these products/technology yourself for activities disturbing international peace and security. 3. Allow any other party to use these products/technology for activities disturbing international peace and security. Also, as purchaser of these products/technology, you agree to follow the procedures for the export or transfer of these products/technology, under the Foreign Exchange and Foreign Trade Law, when you export or transfer the products/technology abroad. Sanken Electric Co.,Ltd. I03-002EA-051006 14/14 |
Price & Availability of SLA7051M |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |